Comfast CF-WU785AC 1300Mbps Adaptador Wi-Fi 2.4 + 5.8GHz Dual Band Dongle Placa de Rede USB 3.0 Sem Fio com 4 Antenas.Função:1- Navegar na internet através de redes wi-fi.2- Realizar monitoramento de pacotesCaracterística:Modo monitor e injeção de pacotes para penetração em redes wi-fi.Potentes 4 antenas 6dbi, mais fortes através das paredes.Velocidade sem fio de alta velocidade de 1300mbps.Interface USB3.0, maior eficiência de transmissão.Especificação:Marca: ComfastModelo: CF-WU785ACChipset: mt7612unCor: pretoFrequência sem fio: 2,412-2,484 GHz, 5,180-5,825 GHzPadrão sem fio: suporte IEEE802.11a/b/g/h/acTaxa de transmissão: 11n: 400Mbps; 11ac: 867MbpsInterface: Micro USB 3.0Antena: 4 banda dupla 6dBiRecursos de segurança: WPA-PSK/WPA2-PSK /WPA2; wepPotência de transmissão: 20dBmSuporte do sistema: para Windows 7/8/8.1/10 (32 bits, 64 bits)(para sistemas Windows xp, Mac, Linux, é necessário baixar o pacote de instalação do driver separadamente)Temperatura de trabalho: 0°C40°CTemperatura de armazenamento: -40°C 70°CUmidade de trabalho: 10% 90% rh sem condensaçãoUmidade de armazenamento: 5% 90% rh sem condensaçãoTamanho do produto: 175 X 101 X 98mmTamanho da embalagem: 277 X 125 X 58mmPeso bruto: 200gIncluído:1 * placa de rede de banda dupla1 * cabo de dados usb1 * ManualWiphy phy0wiphy index: 0max # scan SSIDs: 4max scan IEs length: 2243 bytesmax # sched scan SSIDs: 0max # match sets: 0Retry short limit: 7Retry long limit: 4Coverage class: 0 (up to 0m)Device supports RSN-IBSS.Device supports AP-side u-APSD.Device supports T-DLS.Supported Ciphers:* WEP40 (00-0f-ac:1)* WEP104 (00-0f-ac:5)* TKIP (00-0f-ac:2)* CCMP-128 (00-0f-ac:4)* CCMP-256 (00-0f-ac:10)* GCMP-128 (00-0f-ac:8)* GCMP-256 (00-0f-ac:9)* CMAC (00-0f-ac:6)* CMAC-256 (00-0f-ac:13)* GMAC-128 (00-0f-ac:11)* GMAC-256 (00-0f-ac:12)Available Antennas: TX 0x3 RX 0x3Configured Antennas: TX 0x3 RX 0x3Supported interface modes:* IBSS* managed* AP* AP/VLAN* monitor* mesh point* P2P-client* P2P-GOBand 1:Capabilities: 0x1ffRX LDPCHT20/HT40SM Power Save disabledRX GreenfieldRX HT20 SGIRX HT40 SGITX STBCRX STBC 1-streamMax AMSDU length: 3839 bytesNo DSSS/CCK HT40Maximum RX AMPDU length 65535 bytes (exponent: 0x003)Minimum RX AMPDU time spacing: No restriction (0x00)HT TX/RX MCS rate indexes supported: 0-15Bitrates (non-HT):* 1.0 Mbps (short preamble supported)* 2.0 Mbps (short preamble supported)* 5.5 Mbps (short preamble supported)* 11.0 Mbps (short preamble supported)* 6.0 Mbps* 9.0 Mbps* 12.0 Mbps* 18.0 Mbps* 24.0 Mbps* 36.0 Mbps* 48.0 Mbps* 54.0 MbpsFrequencies:* 2412 MHz [1] (20.0 dBm)* 2417 MHz [2] (20.0 dBm)* 2422 MHz [3] (20.0 dBm)* 2427 MHz [4] (20.0 dBm)* 2432 MHz [5] (20.0 dBm)* 2437 MHz [6] (20.0 dBm)* 2442 MHz [7] (20.0 dBm)* 2447 MHz [8] (20.0 dBm)* 2452 MHz [9] (20.0 dBm)* 2457 MHz [10] (20.0 dBm)* 2462 MHz [11] (20.0 dBm)* 2467 MHz [12] (20.0 dBm) (no IR)* 2472 MHz [13] (20.0 dBm) (no IR)* 2484 MHz [14] (20.0 dBm) (no IR)Band 2:Capabilities: 0x1ffRX LDPCHT20/HT40SM Power Save disabledRX GreenfieldRX HT20 SGIRX HT40 SGITX STBCRX STBC 1-streamMax AMSDU length: 3839 bytesNo DSSS/CCK HT40Maximum RX AMPDU length 65535 bytes (exponent: 0x003)Minimum RX AMPDU time spacing: No restriction (0x00)HT TX/RX MCS rate indexes supported: 0-15VHT Capabilities (0x318001b0):Max MPDU length: 3895Supported Channel Width: neither 160 nor 80+80RX LDPCshort GI (80 MHz)TX STBCRX antenna pattern consistencyTX antenna pattern consistencyVHT RX MCS set:1 streams: MCS 0-92 streams: MCS 0-93 streams: not supported4 streams: not supported5 streams: not supported6 streams: not supported7 streams: not supported8 streams: not supportedVHT RX highest supported: 0 MbpsVHT TX MCS set:1 streams: MCS 0-92 streams: MCS 0-93 streams: not supported4 streams: not supported5 streams: not supported6 streams: not supported7 streams: not supported8 streams: not supportedVHT TX highest supported: 0 MbpsVHT extended NSS: not supportedBitrates (non-HT):* 6.0 Mbps* 9.0 Mbps* 12.0 Mbps* 18.0 Mbps* 24.0 Mbps* 36.0 Mbps* 48.0 Mbps* 54.0 MbpsFrequencies:* 5180 MHz [36] (20.0 dBm) (no IR)* 5200 MHz [40] (20.0 dBm) (no IR)* 5220 MHz [44] (20.0 dBm) (no IR)* 5240 MHz [48] (20.0 dBm) (no IR)* 5260 MHz [52] (20.0 dBm) (no IR, radar detection)* 5280 MHz [56] (20.0 dBm) (no IR, radar detection)* 5300 MHz [60] (20.0 dBm) (no IR, radar detection)* 5320 MHz [64] (20.0 dBm) (no IR, radar detection)* 5500 MHz [100] (20.0 dBm) (no IR, radar detection)* 5520 MHz [104] (20.0 dBm) (no IR, radar detection)* 5540 MHz [108] (20.0 dBm) (no IR, radar detection)* 5560 MHz [112] (20.0 dBm) (no IR, radar detection)* 5580 MHz [116] (20.0 dBm) (no IR, radar detection)* 5600 MHz [120] (20.0 dBm) (no IR, radar detection)* 5620 MHz [124] (20.0 dBm) (no IR, radar detection)* 5640 MHz [128] (20.0 dBm) (no IR, radar detection)* 5660 MHz [132] (20.0 dBm) (no IR, radar detection)* 5680 MHz [136] (20.0 dBm) (no IR, radar detection)* 5700 MHz [140] (20.0 dBm) (no IR, radar detection)* 5720 MHz [144] (20.0 dBm) (no IR, radar detection)* 5745 MHz [149] (20.0 dBm) (no IR)* 5765 MHz [153] (20.0 dBm) (no IR)* 5785 MHz [157] (20.0 dBm) (no IR)* 5805 MHz [161] (20.0 dBm) (no IR)* 5825 MHz [165] (20.0 dBm) (no IR)* 5845 MHz [169] (disabled)* 5865 MHz [173] (disabled)Supported commands:* new_interface* set_interface* new_key* start_ap* new_station* new_mpath* set_mesh_config* set_bss* authenticate* associate* deauthenticate* disassociate* join_ibss* join_mesh* remain_on_channel* set_tx_bitrate_mask* frame* frame_wait_cancel* set_wiphy_netns* set_channel* tdls_mgmt* tdls_oper* probe_client* set_noack_map* register_beacons* start_p2p_device* set_mcast_rate* connect* disconnect* channel_switch* set_qos_map* set_multicast_to_unicast* set_sar_specssoftware interface modes (can always be added):* AP/VLAN* monitorvalid interface combinations:* #{ IBSS } <= 1, #{ managed, AP, mesh point, P2P-client, P2P-GO } <= 2,total <= 2, #channels <= 1, STA/AP BI must matchHT Capability overrides:* MCS: ff ff ff ff ff ff ff ff ff ff* maximum A-MSDU length* supported channel width* short GI for 40 MHz* max A-MPDU length exponent* min MPDU start spacingDevice supports TX status socket option.Device supports HT-IBSS.Device supports SAE with AUTHENTICATE commandDevice supports low priority scan.Device supports scan flush.Device supports AP scan.Device supports per-vif TX power settingDriver supports full state transitions for AP/GO clientsDriver supports a userspace MPMDevice supports active monitor (which will ACK incoming frames)Device supports configuring vdev MAC-addr on create.max # scan plans: 1max scan plan interval: -1max scan plan iterations: 0Supported TX frame types:* IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0* managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0* AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0* AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0* mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0* P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0* P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0* P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0Supported RX frame types:* IBSS: 0x40 0xb0 0xc0 0xd0* managed: 0x40 0xb0 0xd0* AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0* AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0* mesh point: 0xb0 0xc0 0xd0* P2P-client: 0x40 0xd0* P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0* P2P-device: 0x40 0xd0Supported extended features:* [ VHT_IBSS ]: VHT-IBSS* [ RRM ]: RRM* [ FILS_STA ]: STA FILS (Fast Initial Link Setup)* [ CQM_RSSI_LIST ]: multiple CQM_RSSI_THOLD records* [ CONTROL_PORT_OVER_NL80211 ]: control port over nl80211* [ TXQS ]: FQ-CoDel-enabled intermediate TXQs* [ SCAN_RANDOM_SN ]: use random sequence numbers in scans* [ SCAN_MIN_PREQ_CONTENT ]: use probe request with only rate IEs in scans* [ AIRTIME_FAIRNESS ]: airtime fairness scheduling* [ AQL ]: Airtime Queue Limits (AQL